Series 2000-SP Magnehelic® Differential Pressure Gages
Indicate Positive, Negative or Differential, Accurate within 2%
Series 2000-SP Magnehelic® Differential Pressure Gage has a bright red LED on the right of the scale showing when setpoint is reached. Field adjustable from gage face, unit operates on 12-24 VDC. Requires MP or HP style cover and bezel.
NIST CALIBRATION available in Product Configurator.
Starting at $267.30
Specifications
- Service:
- Air and non-combustible, compatible gases. (Natural gas option available.)
- Wetted Materials:
- Consult factory.
- Housing:
- Die cast aluminum case and bezel, with acrylic cover. Exterior finish is coated gray to withstand 168 hour salt spray corrosion test.
- Accuracy:
- ±2% of full scale (±3% on - 0, -100 Pa, -125 Pa, 10MM and ±4% on - 00,-60 Pa, -6MM ranges), throughout range at 70°F (21.1°C).
- Pressure Limits:
- 35 psig (2.41 bar), HP option: 80 psig (5.52 bar).
- Overpressure:
- Relief plug opens at approximately 25 psig (1.72 bar), standard gages only.
- Temperature Limits:
- 20 to 140°F. (-6.67 to 60°C).
- Size:
- 4" (101.6 mm) diameter dial face.
- Mounting Orientation:
- Diaphragm in vertical position. Consult factory for other position orientations.
- Process Connections:
- 1/8" female NPT duplicate high and low pressure taps - one pair side and one pair back.
- Weight:
- 1 lb 2 oz (510 g), MP & HP 2 lb 2 oz (963 g).
- Standard Accessories:
- Two 1/8" NPT plugs for duplicate pressure taps, two 1/8" pipe thread to rubber tubing adapter and three flush mounting adapters with screws. (Mounting and snap ring retainer substituted for 3 adapters in MP & HP gage accessories.)
Model Chart
| EXAMPLE | 2001 | SP-AT | Series 2001-SP-AT Magnehelic® Differential Pressure Gage, range 0-1" w.c., with set point indicator and aluminum tag. |
| RANGE | 2000-00N 2000-00 2000-0 2001 2002 2003 2004 2005 2006 2008 2010 2015 2020 2025 2030 2040 2050 2060 2080 2100 2150 2300-0 2301 2302 2304 2310 2320 2330 2000-00AV 2000-0AV 2001AV 2002AV 2010AV 2201 2202 2203 2204 2205 2210 2215 2220 2230 2000-6MM 2000-10MM 2000-20MM 2000-25MM 2000-50MM 2000-80MM 2000-100MM 2000-150MM 2000-250MM 2300-20MM 2300-30MM 2000-1CM 2000-2CM 2000-5CM 2000-10CM 2000-15CM 2000-20CM 2000-25CM 2000-30CM 2000-40CM 2000-50CM 2000-80CM 2000-100CM 2000-150CM 2000-200CM 2000-250CM 2000-300CM 2300-4CM 2300-10CM 2300-20CM 2300-30CM 2000-60PA 2000-125PA 2000-250PA 2000-500PA 2000-750PA 2300-250PA 2300-500PA 2000-1KPA 2000-1.5KPA 2000-2KPA 2000-3KPA 2000-4KPA 2000-5KPA 2000-8KPA 2000-10KPA 2000-15KPA 2000-20KPA 2000-25KPA 2000-30KPA 2300-1KPA 2300-3KPA |
.05-0-.2" w.c. 0-0.2" w.c. 0-0.5" w.c. 0-1" w.c. 0-2" w.c. 0-3" w.c. 0-4" w.c. 0-5" w.c. 0-6" w.c. 0-8" w.c. 0-10" w.c. 0-15" w.c. 0-20" w.c. 0-25" w.c. 0-30" w.c. 0-40" w.c. 0-50" w.c. 0-60" w.c. 0-80" w.c. 0-100" w.c. 0-150" w.c. .25-0-.25" w.c. .5-0-.5" w.c. 1-0-1" w.c. 2-0-2" w.c. 5-0-5" w.c. 10-0-10" w.c. 15-0-15" w.c. 0-.25" w.c. & 300-2000 FPM AV 0-.5" w.c. & 500-2800 FPM AV 0-1" w.c. & 500-4000 FPM AV 0-2" w.c. & 1000-5600 FPM AV 0-10" w.c. & 2000-12500 FPM AV 0-1 psid 0-2 psid 0-3 psid 0-4 psid 0-5 psid 0-10 psid 0-15 psid 0-20 psid 0-30 psid 0-6 MM w.c. 0-10 MM w.c. 0-20 MM w.c. 0-25 MM w.c. 0-50 MM w.c. 0-80 MM w.c. 0-100 MM w.c. 0-150 MM w.c. 0-250 MM w.c. 10-0-10 MM w.c. 15-0-15 MM w.c. 0-1 CM w.c. 0-2 CM w.c. 0-5 CM w.c. 0-10 CM w.c. 0-15 CM w.c. 0-20 CM w.c. 0-25 CM w.c. 0-30 CM w.c. 0-40 CM w.c. 0-50 CM w.c. 0-80 CM w.c. 0-100 CM w.c. 0-150 CM w.c. 0-200 CM w.c. 0-250 CM w.c. 0-300 CM w.c. 2-0-2 CM w.c. 5-0-5 CM w.c. 10-0-10 CM w.c. 15-0-15 CM w.c. 0-60 Pa 0-125 Pa 0-250 Pa 0-500 Pa 0-750 Pa 125-0-125 Pa 250-0-250 Pa 0-1 kPa 0-1.5 kPa 0-2 kPa 0-3 kPa 0-4 kPa 0-5 kPa 0-8 kPa 0-10 kPa 0-15 kPa 0-20 kPa 0-25 kPa 0-30 kPa .5-0-.5 kPa 1.5-0-1.5 kPa |
|
| OPTION | -AT -COO -ED -G -HC -HP -LT -M -MP -NIST -R -SP -ST -TA -TAMP -Y |
Aluminum Tag Certificate of Origin Energizing Green Scale Overlay Horizontal Calibration (90° Face Up) High Pressure Low Temperature Mirror Scale Overlay Medium Pressure NIST Certificate of Calibration Red Scale Overlay Set Point Indicator Stainless Steel Tag Tilt Angle from Vertical in Degrees (-90 to 90) Tamperproof Knobs Yellow Scale Overlay |
Questions
- Question
- How will installation of a Magnehelic® gage 150' away from the pressure source affect accuracy?
- Answer
- Accuracy will not be affected, but response time will be increased in proportion to the length of the tubing.
- Question
- Can the standard Magnehelic® or Capsuhelic® gage be installed outdoors?
- Answer
- Yes. Front covers are sealed with "O" rings. Capsuhelic vent holes are plugged with foam, and the new high impact acrylic lens material is very resistant to ultra-violet fogging. Additional care is recommended to lead pressure connections downward from the gage and provide as much protection from the elements as possible
- Question
- Can a standard Magnehelic® gage be used for natural gas or propane service?
- Answer
- No. As the silicone diaphragm will be attacked by these gases. A Buna-N diaphragm should be specified.
- Question
- What happens when a Magnehelic® gage equipped with the low temperature option is operated below -20 degrees Fahrenheit (-29 degrees Celsius)?
- Answer
- Below that temperature the accuracy of the gage deteriorates beyond our published specification due to stiffening of the diaphragm.
- Question
- Is National Institute of Standards and Technology traceability available for the Magnehelic® Gage?
- Answer
- No. But Magnehelic® gages can be given a special 6 point calibration check with an NIST traceable master gage and a certificate can be supplied.
- Question
- How do I hook up my Magnehelic® Gage?
- Answer
- In Bulletin A-27 under operation, it explains how to connect the Magnehelic to the following applications: positive pressure, negative pressure, and differential pressure.
- Question
- Your Magnehelic gauge doesn't come with a calibration certificate, do you have any documentation for these gauges to meet these needs?
- Answer
- We have 3 options: (1) We can supply a Certificate of Conformance at no charge if you request that certificate at the time of order. The Certificate of conformance would state that each Magnehelic gauge is calibrated to meet the specifications stated on the spec sheet. (2) We offer a factory calibration “-FC” as an option that is a certificate of the standard calibration points at the time of manufacture, for a small fee. (3) We can also provide a NIST-traceable calibration for an extra charge per gage if that is required. To get the NIST-traceable calibration, you would simply add a “-NIST” to the end of your part number. NIST-traceable calibrations will come with the 6 point calibration certificate. We recommend “periodic calibration” for our Magnehelic, though we leave the specific time-frame up to the end user, since different organizations have different requirements (i.e. government groups often require more frequent calibrations.) If you choose to have the NIST traceable calibration done, the NIST group (the National Institute of Standards and Technology) dictates yearly calibration and it will be printed on the certificate.
- Question
- I am looking to measure velocity in a 4" pipe that is used as air conveyance. We use an eductor and a single stage blower to produce air flow. I am looking to measure pressure and velocity. I purchased a Dwyer Pitot tube, 167-7 108024-00 for the job, and I want to match with the right gauge. I need to be in the range of 2600 cuft/min at maybe 0.5psi. Can you direct me to the right gauge with that information?
- Answer
- To monitor flow through your 4” pipe, you will have to size the appropriate differential pressure gage. A very common gage that is used will be our Series 2000 Magnehelic gage. This gage can be ordered with a square root output that will direct read in flow units. Upon ordering this part, you will have to specify the maximum differential pressure at your desired flow rate. The following text will bring you to the equations necessary to compute this differential (velocity) pressure. This can also be found in the APPLICATION GUIDES section of our website.
- Question
- I have a Magnehelic gage 2000-00N I purchased for a clean room. Should the installers set the "set" screw to get the gage back to (0) or will that mess up the calibration? My invoice # if you need to look at what I purchased is 04844623.
- Answer
- After the Magnehelic has been installed, disconnect pressure lines to vent both sides of the gage to the atmosphere and re-zero. This will not mess up the calibration. This should be done occasionally.
- Question
- What restrictions, if any, are imposed for the Magnehelic® and Photohelic® gages in vacuum service?
- Answer
- In applications involving higher vacuums than 20" Hg, leakage due to gage housing porosity becomes the limiting factor.
Write Your Own Review
| Model | Description | Availability* | Price | |
|---|---|---|---|---|
| A-135 | Silicone rubber gasket for panel mounting (Series 2000, DM-2000, DM-1000, 605) | 1-3 days* |
$5.40 |
|
| A-286 | 4-1/2" Gage panel mounting flange | 1-3 days* |
$16.05 |
|
| A-299 | Mounting bracket flush mount Magnehelic® gage in bracket. Bracket is then surface mounted . Steel with gray hammertone epoxy finish. 6.3" x 7.7" x 4.0", 1.30 lb. | 1-3 days* |
$41.55 |
|
| A-300 | Flat aluminum bracket for flush mounting Magnehelic® gage. 6.8" x 6.0" x .1", .35 lb. | 1-3 days* |
$36.65 |
|
| A-310A | 3-way vent valve, plastic, 1/8" NPT to 1/4" metal tubing, 80 psi rating, replaces former Model A-310 (brass). 2.3" x .8" x .1", .10 lb. | 1-3 days* |
$23.75 |
|
| A-320-B-SS | Instrument enclosure, 304SS, brushed finish, compatible with 2000 Magnehelic® gage, DM-2000 differential pressure transmitter | 1-3 days* |
$847.65 |
|
| A-320-B1 | Weatherproof enclosure, ABS, compatible with Series 3000MR/MRS Photohelic®, Series 605 Magnehelic®, Series DH3 Digihelic® (to fit, the casing on the electrical plug must be removed), Series 2000 Magnehelic® with medium and high pressure options | 1-3 days* |
$326.00 |
|
| A-320-BC | Weatherproof enclosure, ABS, compatible with Series 2000 Magnehelic®, DM-1000 DigiMag®, DM-2000, Series 605 (with -SS option), instruments with backwards compatible bezel option | 1-3 days* |
$326.00 |
|
| A-321 | Brass safety relief valve, protects Magnehelic® gage or Photohelic® switch/gage against over pressure due to regulator failure, etc, opens at 10 psi. Mounts in tee fitting. 1/4" NPT(M) (use two for DP application). .5" x .5" x 1.5", .10 .lb | 1-3 days* |
$57.25 |
|
| A-368 | Surface mounting plate, aluminum, for Magnehelic® gage. | 1-3 days* |
$10.55 |
|
| A-369 | Stand-hang bracket, aluminum, for Magnehelic® gage. | 1-3 days* |
$16.50 |
|
| A-371 | Surface mounting bracket, use with Photohelic® switch/gage on horizontal or vertical surfaces, also for Capsu-Photohelic® switch/gage on vertical only. Also Magnehelic® -MP, -HP models. | 1-3 days* |
$52.10 |
|
| A-432 | Plastic carrying case for Magnehelic® gage of standard range, except high pressure connection, includes 9 ft (2.7m) of 3/16" ID rubber tubing, stand-hang bracket & terminal tube with holder. 9.1" x 7.4" x 3.6", 1.30 .lb | 1-3 days* |
$64.00 |
|
| A-464 | Flush mount kit for Magnehelic® gages (Magnehelic® sold separately) | 1-3 days* |
$28.10 |
|
| A-464-SS | Stainless steel flush mounting kit for the Magnehelic® gages (Magnehelic® sold separately) | 1-3 days* |
$131.45 |
|
| A-481 | Installer kit, (includes 2 static pressure tips and PVC tubing). | 1-3 days* |
$6.60 |
|
| A-605 | Air filter kit - adapts any standard Magnehelic® gage for use as an air filter gage. Includes aluminum surface mounting bracket with screws, (2) 5 ft (1.5 m) lengths of 1/4" aluminum tubing, (2) static pressure tips & (2) molded plastic vent valves. | 1-3 days* |
$49.80 |
|
| 200068-51 | Mounting hardware kit for standard Magnehelics® (not MP or HP). Included in the kit: 2 each: A-339 adapters, A-330 pipe adapters; 3 each: mounting lugs, long screws, short screws) | 1-3 days* |
$12.40 |